Chapter 1 Introduction
1.1 Interchangeability
1.1.1 Interchangeability and its advantages
1.2 Standardization
1.2.1 Standard and standardization
1.2.2 Related standards on geometrical interchangeability
1.3 Series of Preferred Values
1.4 What We Can Learn from This Course
Questions
Excercise
Chapter 2 Limits and Fits of Plain Workpiece
2.1 Basic Terms and Definitions
2.1.1 Terms and definitions about geometrical features
2.1.2 Shaft and hole
2.1.3 Terms and definitions about size, deviation, tolerance
2.1.4 Terms and definitions about fits
2.2 Standards of Limits and Fits
2.2.1 Fit system
2.2.2 Symbols, designation and indication on engineering drawings
2.2.3 Standard tolerance series
2.2.4 Series of fundamental deviation
2.2.5 Standardization of tolerance classes and fits
2.3 Selection of Limits and Fits
2.3.1 Selection of basic system of fit
2.3.2 Selection of standard tolerance grades
2.3.3 Selection of fits
2.3.4 Calculation method
2.4 General Dimension Tolerance
2.4.1 General tolerances of linear sizes
2.4.2 Indication of general tolerance on drawing
2.4.3 General tolerance grades and values
Questions
Exercises
Chapter 3 Fundamentals of Geometrical Quantity Measurement
3.1 Introduction
3.1.1 Concept of measurement and inspection
3.1.2 Measuring processing
3.2 Measurement Standard~Datum~Data and Dissemination of Length and Angle ..
3.2.1 Standard of length and angle
3.2.2 Dissemination system of length and angle
3.2.3 Gauge blocks and their applications
3.3 Metrological Equipment and Measurement Methods
3.3.1 Metrological equipment
3.3.2 Measurement methods
3.4 Measurement Error and Data Treatment
3.4.1 Designation of measurement error
3.4.2 Source of measurement error
3.4.3 Kinds and properties of measurement error
3.4.4 Measurement accuracyprecision
Questions
Exercises
Chapter 4 Geometrical Tolerances
4.1 General
4.1.1 Cause of geometrical error and effects on performance
4.1.2 Basic terms and definitions
4.1.3 Symbols and characteristics of geometrical tolerances
4.1.4 Geometrical tolerance zone
4.2 Indication of Geometrical Tolerance on Engineer Drawings
4.2.1 Tolerance frame
4.2.2 Indication of datum on engineering drawings
4.2.3 Indication of toleranced features
4.2.4 Theoretical exact dimension TED
4.3 Definition of Geometrical Tolerances
4.3.1 Definition and characteristics of form tolerances
4.3.2 Definition and characteristics of orientation tolerances
4.3.3 Definition and characteristics of location tolerance
4.3.4 Definition and characteristics of run-out tolerance
4.4 Tolerance Principles
4.4.1 Terms and definition about tolerance principle
4.4.2 Independency principle
4.4.3 Envelope requirement ER
4.4.4 Maximum material requirement MMR
4.5 Assessment and Measurement of Geometrical Deviations
4.5.1 Assessment of geometrical deviation
4.5.2 Establishment and embodiment of datum
4.5.3 Measuring prescriptions of geometrical deviations
4.6 Selection of Geometrical Tolerance
4.6.1 General
4.6.2 Selection of datum
4.6.3 Selection of geometrical principle
4.6.4 Selection of geometrical tolerance value
4.7 General Geometrical Tolerances
4.7.1 General geometrical tolerances grades
4.7.2 Indication of general geometrical tolerance
Questions
Chapter 5 Surface Roughness
5.1 Introduction
5.2 Basic Terms and Definitions
5.3 Main Evaluation Parameters of Surface Roughness
5.3.1 Amptitude parameters peak and vallye
5.3.2 Spacing Parameters
5.3.3 Curves and relative parameters
5.4 Principles for Selecting Surface Roughness Parameters
5.5 Graphical Symbols and Notation
5.6 Indications of Surface Texture Requirements on Engineering Drawing
5.7 Measurement Techniques
5.7.1 Method of comparing with standard sample
5.7.2 Light section method
5.7.3 Interferometric method
5.7.4 Stylus instruments
5.7.5 Optical instruments
Exercises
Chapter 6 Measurement of Plain Workpieces
6.1 Basic Concepts
6.1. I Workpiece inspection principles, safety margins and acceptance limits
6.1.2 Selection of measurement tools
6.2 Plain Limit Gauges
6.2.1 Functions and kinds of plain limit gauges
6.2.2 Design principle of plain limit gauges
6.2.3 Tolerance of the plain limit gauge
6.2.4 Design steps and calculationof the limits size
Questions
Exercises
Chapter 7 Tolerances and Fits of Rolling Bearing
7.1 General
7.2 Introduction of Rolling Bearings
7.2.1 Construction and classification of rolling bearing
7.2.2 Analysis of working performance of rolling bearings
7.2.3 Internal clearance of rolling bearings
7.2.4 Tolerance grades Of rolling bearings and applications
7.2.5 Tolerance zone of rolling bearings
7.3 Selection of Tolerance and Rolling Bearings Fits
7.3.1 Selection of Rolling Bearing Fits
7.3.2 Geometrical tolerance requirements for shafts and holes fitted with rolling bearings
7.3.3 Surface roughness requirements of shafts and holes fitted with rolling bearings
Exercises
Chapter 8 Tolerances and Measurement of Cylinder Screw
8.1 Introduction
8. 1.1 Classification and requirements of thread
8.1.2 Basic common thread tooth type and geometrical parameters
8.2 Influence of Thread Geometrical Deviation on Thread Interchangeability
8.2.1 Influence of pitch diameter deviation △D2a, △d2a on thread interchangeability
8.2.2 Influence of pitch deviation on screw thread interchangeability
8.2.3 Influence of thread half angle deviation △α2 on screw thread interchangeability
8.2.4 Calculation of virtual pitch diameter
8.2.5 Conditions to guarantee the screw thread interchangeability
8.3 General Purpose Screw Threads-tolerance Zones for Screw Thread
8.3.1 Tolerance grades
8.3.2 Fundamental deviation tolerance positions
8.3.3 Length of thread engagement
8.3.4 Thread selection, tolerance zone and fits
8.3.5 Thread marking
8.3.6 Inspection of screw thread
Questions
Exercises
Chapter 9 Tolerances and Fits of Keys and Splines
9.1 Tolerances and Fits of Rectangular Keys Connection
9.1.1 Introduction of rectangular keys connection structure
9.1.2 Tolerance and fits of the rectangular key connection
9.2 Tolerances and Fits of Straight-sided Spline Connection
9.2.1 Introduction of spline connection structure
9.2.2 Designation
9.2.3 Tolerances and fits of straight-sided spline connections
Questions
Exercises
Chapter 10 Accuracy Design of Cylindrical Involute Gear
10.1 General
10.2 Evaluation Parameters of Cylindrical Involute Gear
10.2.1 Definition of evaluation parameters
10.2.3 Allowable values of every deviation of cylindrical involute gears
10.3 Accuracy Design of Cylindrical Involute Gears
10.3.1 Selection of accuracy grade
10.3.2 Selection of evaluation parameters
10.3.3 Detemination of gear backlash
10.3.4 Detemination of gear pair precision
10.3.5 Detemination of gear blank accuracy
Questions
Chapter 11 Dimension Chain
11.1 Basic Concepts and Terms of Dimension Chain
11.1.1 Basic concepts and terms
11.1.2 Forms of dimension chain
11.1.3 Establishment of dimension chain
11.2 Tolerance Calculations of Size Chain
11.2.1 Types of dimension chain calculation
11.2.2 Extreme value method
11.2.3 Probability method
11.3 Methods to Fulfill Tolerance Stacks of Size Chain
11.3.1 Complete interchange method
11.3.2 Large number interchange method
11.3.3 Grouping method
Questions
Exercises
References
購物車/收銀台(
0
) | 在線留言板
| 付款方式
| 聯絡我們
| 運費計算
| 幫助中心 |
加入書簽
HOME
新書上架
